Learn More +

Zircon Sand In The Foundry: Installation, Commissioning And Troubleshooting

Why Zircon Sand Is Used and What Makes It Difficult

Zircon sand is a naturally occurring zirconium silicate that is processed, classified and dried for use as a moulding sand. Its appeal in the foundry comes from a combination of properties: it is chemically inert, it does not react readily with molten metal, it has a very low coefficient of thermal expansion, and it holds its surface on the mould long enough to support heavy and thin sections alike. Because of that stability, zircon is routinely used where the risk of metal penetration, mould reaction or sand inclusion is high, in heavy ferrous casting, in moulds with fine detail, and in the facing layers of large moulds where chemical attack would otherwise be severe.

The same physical properties that make zircon valuable also make it difficult to handle. It is roughly two and a half times as dense as silica sand, so conveying, elevating and storing it demands more power and more robust equipment than a conventional sand plant was ever designed for. Every problem seen on a zircon line usually traces back to one of three factors: moisture control, bonding, or sand distribution. Troubleshooting zircon is therefore mostly a matter of working through those three systematically rather than reacting to the defect in front of you.

Physical and Chemical Properties That Govern Behaviour

Zircon is sold in several size bands and with different levels of magnetic contamination, and the specification written at the desk determines the sort of behaviour seen on the floor. The table below gives the range of properties a foundry should expect from a standard zircon sand supply.

PropertyTypical range for moulding grade zirconWhy it matters on the shop floor
Specific gravityApproximately 4.6 to 4.7Sets conveying power requirement and bin load
Bulk densityApproximately 2.3 to 2.6 g/cm3Determines storage footprint needed per tonne
Melting pointApproximately 2550 to 2600 CExplains resistance to penetration and reaction
Coefficient of thermal expansionApproximately 4 to 5 times 10 to the power of minus 6 per CVery low, so thermal shock damage is rare
Standard grain sizeApproximately 0.11 to 0.30 mm depending on gradeControls surface finish and sand inclusion risk
AngularitySubangular to angularInfluences mould strength and compactability
MoistureTypically below 0.5 percent as suppliedExcess moisture causes gas and lamination
Magnetic contaminationVery low for graded productMetallic inclusions appear as sparkler or slag spots

Preparing and Storing the Sand

Zircon arrives dry and must stay dry. Storage is the first place problems originate, because a bin that is not properly vented or roofed will collect condensation in humid weather, and damp zircon that is fed to a binder system will produce trapped steam rather than a coherent mould. Zircon should be stored in covered bins with drainage, on a raised floor. Bins should be sized so that the sand turns over within a reasonable period, since long residence encourages segregation of the size fractions and dead spots where moisture accumulates.

Conveying requires attention as well. Bucket elevators, belt conveyors, screw conveyors and pneumatic systems all work, but the minimum practical belt speed and the load factor must be set for a material of this density. Vibrating equipment, chutes and dead boxes need to be lined or sized for the impact load. Where pneumatic conveying is used, the air volume must be recalibrated for the higher density, and separators must be checked for capacity, because an undersized separator will spill sand back into the duct.

Installation: Getting the Plant Right from the Start

Most zircon installation faults are design faults that appear later as operating problems. The main items deserve attention before the plant is commissioned. First, structure and bins must be sized for the higher dead load. Second, the shakeout and recycling route must be planned, since zircon that is not reclaimed ends up in waste sand at a cost per tonne far higher than for silica. Third, dust control must be specified at the transfer points, because zircon dust is finer and more irritating to breathe than silica dust, and because a dusty handling point means air entrainment into the mix.

Distribution is the fourth item and the one most often neglected. Zircon does not flow as freely as silica. If the sand is fed into the mix through a simple gravity chute it will bridge, particularly when the sand is slightly damp. Small vibrating distributors, or a powered feeder with a controlled delivery rate, are worth installing at the mixing station and at the moulding station. The same applies to the sand returned from knock-out: an uneven reclaim stream produces an uneven mix and an uneven mould, and that shows up as scatter in the final casting.

Practical commissioning checks

  • Confirm the actual bulk density and moisture of the incoming sand by measurement, not by inspection.
  • Verify that conveyor and elevator motors run at the design load without stalling or overloading.
  • Check that separators and dust collectors handle the density without recycling loss.
  • Run the reclaim line and confirm a stable return rate from knock-out.
  • Measure the variability of the mould hardness across a full plate, from one end to the other.

Bonding: The Usual Weak Point

Zircon sand is commonly bonded with resin systems, with inorganic binders such as silicate, or with a combination of resin and refractory coating. Whichever system is used, the bond has to hold a very dense, low expansion grain at temperatures well above the melting point of the binder, and the mould must then release cleanly. Resin bonded zircon produces excellent moulds with high strength and good dimensional accuracy, but release properties depend heavily on accurate resin addition, uniform sand temperature and correct catalyst dosage.

Inorganic silicate bonding is more tolerant of variable conditions and easier to knock out, but it produces a more hygroscopic mould that is vulnerable to moisture pickup in storage. Whichever route is used, the variables that must be controlled are the same: sand moisture, sand temperature, resin dosage, mixing time and mixing energy.

Commissioning the Process and Holding It Stable

Commissioning a zircon line should begin with a deliberately simple mould, so that any defect can be attributed unambiguously. Start by establishing the base recipe for the sand to resin ratio, the mixing time needed for uniform coating and the mould density that gives acceptable hardness. Only once the base process is stable should the number of variables be increased, whether that means changing the binder chemistry, adding coating or increasing the complexity of the pattern.

It is worth recording a small number of indicators daily through the first weeks of production. Sand temperature and moisture at the mixer, resin addition rate, mixing time, reclaim percentage, cycle time and scrap rate by defect code are enough to detect drift. Most zircon problems that look mysterious turn out to be a slow drift in one of these values, and a simple daily record usually identifies it faster than any amount of inspection.

Control pointIndicative starting rangeSymptom when it drifts
Sand moistureBelow 0.5 percent, adjusted to the binderLamination, blowholes, soft mould faces
Sand temperatureClose to the binder working rangeSlow cure, weak mould, unstable hardness
Sand to resin ratioSet by trial, then held fixedLow strength or heavy smoke on knockout
Mixing timeLong enough for uniform coatingSand streaks, inclusion, poor surface finish
Reclaim fractionSet by contamination and gradingDrifting properties, rising dust and waste
Mould densityUniform across the plateScatter, dimensional variation, poor fill

Troubleshooting the Common Defects

When a defect appears, the temptation is to change the resin or the sand. That usually hides the cause rather than removing it. A more reliable approach is to classify the defect first, since the classification narrows the suspect list immediately. Surface defects point towards sand condition, bonding or distribution. Internal defects point towards gas, moisture or inclusion. Scattering and dimensional faults point towards mould strength, fill and weight.

Sand inclusion and surface roughness

Sand inclusion on the casting surface is usually a distribution or mixing problem rather than a chemistry problem. Check first that the sand entering the mould is uniform, that the vibrating distributor is delivering evenly and that the mould box is not being overfilled. Then confirm that mixing time is sufficient for the binder to coat the grains, since poorly coated grains are shed directly onto the casting. Coarse sand, a high reclaim fraction and a hot mixer can all aggravate the same symptom.

Blowholes and gas porosity

Blowholes fall into two very different families. Fine, dispersed blowholes point to gas trapped in the mould, which on a zircon line usually means moisture in the sand, an over-applied coating or an excessive binder addition with insufficient drying. Larger, singly distributed blowholes more often indicate a fill problem, where the metal traps air while filling the cavity. The remedy differs sharply: improve drying and reduce moisture for the first family, and improve fill rate and venting for the second.

Scabbing, veining and penetration

Scabbing on zircon is uncommon, since the low thermal expansion of the sand resists the mechanism that drives it in silica. When scabbing does occur, look at mould strength, at expansion allowance and at the drying of any coating. Veining is similarly rare and points to mould weakness or a gap in the mould joint. Metal penetration into the mould face is the classic zircon failure, and it happens when the metal exceeds the local heat transfer capacity of the sand. The countermeasures are a face sand of suitable grain size, adequate mould density, a good coat of mould paint or coat and enough drying before pouring.

Difficult knockout and poor sand regeneration

If castings will not knock out cleanly, the mould is usually too strong for the temperature it reached, which points at an over-catalysed or over-cured resin bond rather than at the sand. Reduce catalyst, shorten the cycle or move to a bond that releases more readily. Poor regeneration of reclaim is a different problem: it usually indicates that the knock-out is damaging the grain, that the magnetic separator is removing too much or too little metal, or that the grading screen is set too fine and is pushing usable sand into the waste stream.

Working Principle and Practice Summary

The working principle behind all of the above is consistent. Zircon sand is a stable, dense, low expansion grain that resists chemical attack and thermal shock, and it will hold a mould in good condition provided the sand is dry and clean, the bond is applied accurately and the mould is dense and well filled. The material is forgiving of a great deal, but it punishes inconsistency more than silica does, because a stable grain amplifies any variation in the mix into a variation in the casting.

Two habits make the largest difference in practice: measuring the sand rather than assuming it, and logging defects by code so that a recurring pattern becomes visible over weeks.

Conclusion

Zircon sand rewards the foundry that treats it as a distinct material rather than a heavier substitute for silica. Its strengths, exceptional refractoriness, low thermal expansion and chemical inertness, are exactly why it is specified for heavy castings, detailed patterns and moulds at high risk of penetration. Its difficulties, weight, poor wettability, sensitivity to moisture and heavy wear on handling equipment, are all manageable through storage design, purpose built distribution, accurate binder dosing and disciplined control of moisture, temperature and reclaim. Install the plant with the density in mind, commission with a simple recipe, record the process variables from day one and troubleshoot by defect family rather than by instinct. Done this way, a zircon line becomes one of the more predictable operations in the foundry, and the extra cost per tonne is justified by the castings that no longer arrive damaged.

2026/11/20 10:49:09 8 Click

Copy right © 2019 INTERNATIONAL TRADING CO., LTD.