Learn More +

Dolomite In Practice: Firing, Installation And Troubleshooting On The Shop Floor

Dolomite is one of those materials that looks simple on a purchase order and behaves unpredictably in practice. A nominal calcium magnesium carbonate delivered in loose or bagged form can contain a wide spread of magnesium content, variable moisture and a crystal structure that decides how it decomposes on firing. Once it is calcined into doloma, the same material becomes a stable, high temperature flux that reacts with silica, and the reaction is exactly where most installation and process problems begin. This guide follows dolomite from the raw rock through the kiln, into the working installation, and into the troubleshooting steps that follow when the lining or the batch behaves badly.

Raw Dolomite And Why The Rock Matters

Dolomite is a calcium magnesium carbonate mineral, conventionally written as CaMg(CO3)2. In the raw state it is a soft, light-coloured rock that can contain variable amounts of calcite, clay and iron compounds. Two figures decide how a lot will behave: the magnesium carbonate share, which is usually expressed as the MgO content after calcination, and the moisture held in the rock as mined.

Magnesium content changes the temperature at which the carbonates break down and the temperature at which the resulting oxides sinter. A dolomite with a higher magnesium share is generally more refractory and more resistant to slag attack, but it also needs a higher calcination temperature to reach a fully dense product. Iron and clay act as fluxes: they lower the sintering temperature of the fired material and reduce its refractoriness. For most furnace and kiln work the practical threshold is low iron content, because iron compounds in a doloma lining form low melting glasses that corrode the surrounding brick.

Calcination: What Actually Happens In The Kiln

Heating raw dolomite drives off carbon dioxide in two overlapping steps. Calcium carbonate decomposes first, at a temperature in the region of 700 to 900 degrees Celsius depending on the partial pressure of carbon dioxide in the kiln atmosphere. Magnesium carbonate decomposes later and requires more heat, often in the region of 1000 to 1100 degrees Celsius. The material that leaves the kiln is a mixture of calcium oxide and magnesium oxide, and this is the doloma that is installed.

The critical quality issue is that the calcination must be complete but the sintering must not be excessive. Under-calcined material still contains carbonate, which continues to release gas after installation and causes the lining to crack or spall as it carbonates in service. Over-sintered material is hard, dense and slow to react, which limits the slag penetration and bonding behaviour expected of a working doloma. Table 1 summarises the conditions and the results to watch for.

Calcination conditionPhysical resultInstallation symptomService behaviour
Incomplete, carbonate remainsLight, friable, dusty grainsShrinkage cracks within days of heatingSpalling as the residual carbonate expands
Correctly calcinedUniform granules, clean fractureStays in place through first heat-upGradual slag reaction and self glazing
Over-sinteredDense hard lumps, low reactivityPoor bonding between coursesShort service life from shallow penetration
Over-oxidised or iron richBrown or grey discolourationSlag runs low and corrodes the brickFast chemical wear at the hot face

Doloma, Dead Burned Dolomite And The Sintering Reaction

The term doloma refers to the calcined material, while dead burned dolomite is a denser, more sintered variant produced at higher temperature or with a controlled firing cycle. The distinction matters because a plant that expects the reactivity of a lightly sintered doloma and receives a dense dead burned product will see slow bonding and rapid penetration by slag.

The working principle of a doloma lining is a chemical one. The calcium oxide component reacts with silica from the slag to form calcium silicate, and the magnesium oxide reacts to form magnesium silicate. These reaction products are glassy and seal the surface, creating a protective layer that slows further chemical attack. The reaction is exothermic, which means the heat released during the first contact with slag raises the local temperature and accelerates the reaction further. A good doloma lining therefore has a slightly generous working temperature at the start of a campaign and a controlled cooling rate at the end, so the reaction layer can cool without cracking.

Installation Practice That Prevents Most Failures

Most installation problems are mechanical rather than chemical. The first rule is to dry the material properly before it enters the hot face. Even a small amount of free moisture in a bulk doloma charge turns into steam at temperature, and the steam pressure inside a dense packed lining is enough to spall the material out. The second rule is to store the material dry and to use up older stock first, because doloma stored in damp conditions picks up moisture and loses its free-flowing behaviour, which makes charging uneven.

The third rule is to pay attention to the working interface between the doloma and the brick behind it. A layer of graded crushed doloma or a graded refractory powder between the two is used to make the joint compliant, so that thermal expansion in the working lining does not crack the shell brick. Skipping this layer transfers the differential movement into the doloma itself, and the cracks then appear in the material rather than in the joint.

Charging discipline matters as much as material quality. Keep the layer thickness uniform, compact lightly rather than heavily, and never mix in material from an old broken lining without removing the fused slag crust, because that crust behaves like a flux and ruins the reaction layer of the new charge. The choice between a dry-packed charge and a wet-bonded installation, and between a monolithic brick and a granular layer, follows from the same three questions: how the lining will be heated, how much it will be allowed to move, and how it will be repaired at the end of a campaign.

Common Failure Modes And How To Recognise Them

Troubleshooting starts with the shape of the damage. Cracks that run vertically through the working face usually point to thermal shock or to the expansion being taken by the lining instead of the joint. Spalling, where a layer detaches in flakes, points to thermal gradients combined with a bonding problem, and it is often seen in the first cycle after installation. Erosion and grooving at the slag line point to a chemistry problem rather than a mechanical one. Swelling and outward movement of the lining usually mean that carbonation is happening, in other words the material was not fully calcined before it was installed.

Table 2 lists the symptom, the likely cause and the corrective action for the most common problems encountered on doloma linings and doloma-bearing batches. The pattern of the damage matters more than the depth of it: a problem that appears in every charge is usually a specification problem, while a problem that appears once after a particular batch is usually an operational one.

SymptomLikely causeCorrective action
Vertical cracks in the working faceExpansion restrained, missing compliant jointIntroduce a graded joint layer and revise the expansion allowance
Flaking spall after the first heat-upResidual moisture or insufficient compactionDry the charge further, improve charging and ramp more slowly
Grooving at the slag lineExcess iron or silica in the liningMove to a lower iron grade and check the slag chemistry
Outward swelling of the liningResidual carbonate carbonating in serviceIncrease calcination temperature and hold time, and re-test loss on ignition
Short life, shallow penetrationOver-sintered material reacting slowlyRequest a less dense product or adjust the firing cycle
Uneven wear across the faceNon-uniform charging densityStandardise the charging procedure and the layer thickness

Dosage In Glass And Metallurgical Batches

Dolomite is also used far outside refractory work, as a batch component in glass melting and in steelmaking, and the same habit of careless dosing causes trouble in both. In glass, dolomite contributes both lime and magnesia, and it is also one of the important fluxes that helps melt the batch. The ratio of dolomite to limestone and to the other raw materials decides the final melting behaviour, the viscosity of the melt and the tendency of the glass to devitrify. The practical rule is to keep the dolomite fraction of the batch constant and to correct for the actual analysis of the incoming lot, because a variation of a few per cent in the magnesium share changes the melt noticeably.

In steelmaking, dolomite is charged as a flux and as a slag conditioner. The specifications that matter are the loss on ignition, the size distribution and the consistency between lots. A lump that is too large will not dissolve in the slag in the available time and will end up as undissolved material in the tap, while a dusty lot will generate an excessive heat load and disturb the slag chemistry. Sizing should therefore be matched to the furnace and the residence time rather than to what is convenient to transport.

Testing And Quality Control On Site

Three simple checks catch most problems before they reach the furnace. The first is loss on ignition on the incoming lot, which is a direct proxy for how completely the material has been calcined and how much gas it will release later. The second is a size analysis by screening, which confirms that the material matches the charging equipment and the melting or sintering rate. The third is a simple density and surface appearance check, which detects contamination with fines or with fragments of old lining that were not removed before delivery.

All three are inexpensive and can be performed by the receiving team rather than by an outside laboratory. When a lot fails, the important step is to quarantine it rather than to blend it into a working batch. Blending a marginal lot into good material spreads the problem across the whole stockpile and makes the cause almost impossible to find later.

Conclusion

Dolomite rewards a process view more than a product view, because nearly every failure on a doloma charge or in a doloma batch traces back to a decision made before the material reached the furnace. Raw rock quality sets the calcination window, calcination sets the density and the residual carbonate, density sets the reaction rate with slag, and installation and dosing discipline set whether the material behaves as designed. Understanding the decomposition sequence, controlling the reaction layer, drying the charge, keeping the joint compliant and testing incoming lots consistently are the practical steps that separate a lining that lasts a full campaign from one that fails in the first week.

54 Click

Copy right © 2019 INTERNATIONAL TRADING CO., LTD.